Post your scores or get advice on how to better them.
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 11 Jan 2006, 22:09
I can't seem to overclock my 6800LE after I've softmodded it. Only when I disable a few pipelines am I able too.
Am I better off with 16 pipelines with stock speeds of 300 and 700 clocks OR is 12 pipelines (with overclocking posible) better?
Knowledge isn't power, but the ability to apply knowledge is true power.
Bobendren
Registered User
Posts: 2202 Joined: 03 Oct 2004, 02:00
Location: DBN
Contact:
Post
by Bobendren » 11 Jan 2006, 22:11
That is usually the case.
Just run some benchmarks and compare.
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 11 Jan 2006, 22:24
I ran Aquamark3 with 16 pl and scored 42230, Then scored 44458 with 12 pl and a little overclocking. But then scored 42350 when I increased the clock speeds even more.
Is that normal?
Knowledge isn't power, but the ability to apply knowledge is true power.
Syndicate
Registered User
Posts: 300 Joined: 10 Jul 2005, 02:00
Contact:
Post
by Syndicate » 11 Jan 2006, 22:27
Run 3Dmark03 with all the pipes unlocked, then at the part where the girl attack's the trolls, watch for pixilation, if it does it means that one pipe is damaged, normally bit 03, then disable it and try overclock the RAM and GPU.
Also I’ve got a very nice Bios flash for it.
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 11 Jan 2006, 22:30
Thanx Carly! I'll check it out
BTW: What does the the BIOS flash do exactly?
Knowledge isn't power, but the ability to apply knowledge is true power.
Bobendren
Registered User
Posts: 2202 Joined: 03 Oct 2004, 02:00
Location: DBN
Contact:
Post
by Bobendren » 11 Jan 2006, 22:35
If differs with every run. Take an average of 3 runs maybe?
gifs
Registered User
Posts: 237 Joined: 23 Dec 2005, 02:00
Post
by gifs » 11 Jan 2006, 22:55
I've got the same card and I unlocked an extra 4 four pipelines (the other 4 are damaged) so it runs at 12/6 with speeds of 375 and 871
I scored about 8000 in 3Dmark03
But this was on my P4 2GHz with 512MB SDR (PC133) RAM
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 11 Jan 2006, 23:06
Thanx for the link! I'm trying to track down 3DMark03 somewhere. Will report back soon.
Knowledge isn't power, but the ability to apply knowledge is true power.
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 11 Jan 2006, 23:39
I want to backup the standard bios, but where do I find it?
How do I flash the BIOS btw?
Knowledge isn't power, but the ability to apply knowledge is true power.
Syndicate
Registered User
Posts: 300 Joined: 10 Jul 2005, 02:00
Contact:
Post
by Syndicate » 11 Jan 2006, 23:43
You have to use NV flash, and a stiffy disk, but make sure you have a old Pci card just incase it does not work properly.
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 11 Jan 2006, 23:52
Excuse my feeble knowledge base of flashing, etc... - old Pci card???
I read somewhere else that I can also use Winfox ( which comes with the card), but I don't see any options for doing that?
Knowledge isn't power, but the ability to apply knowledge is true power.
Syndicate
Registered User
Posts: 300 Joined: 10 Jul 2005, 02:00
Contact:
Post
by Syndicate » 12 Jan 2006, 06:56
Don't know never used that befor.
halo
Registered User
Posts: 2412 Joined: 30 Apr 2003, 02:00
Location: on a ring, far,far away
Contact:
Post
by halo » 12 Jan 2006, 08:56
mt-warrior, on this months pcf they have a step by step walkthrough on how to overclock that card... would take a look if i was you...
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 12 Jan 2006, 14:12
Well halo... I have read the article and they only talk about softmodding it. They don't discuss the overclocking of the card.
but thanx anyway.
Knowledge isn't power, but the ability to apply knowledge is true power.
VoodooProphetII
Registered User
Posts: 1196 Joined: 06 Dec 2004, 02:00
Location: Ezulwini....Swaziland
Post
by VoodooProphetII » 12 Jan 2006, 14:25
OVERCLOCK FIRST then you softmod, that is the only way it worked for me...
mt-warrior
Registered User
Posts: 106 Joined: 27 May 2005, 02:00
Location: Cape Town
Post
by mt-warrior » 12 Jan 2006, 14:37
VoodooProphetII - What are your clock settings? Mine won't go higher than 350/810 and it's set to 12/6
Knowledge isn't power, but the ability to apply knowledge is true power.
VoodooProphetII
Registered User
Posts: 1196 Joined: 06 Dec 2004, 02:00
Location: Ezulwini....Swaziland
Post
by VoodooProphetII » 12 Jan 2006, 15:31
I went up to 380 and 800 if my memory serves me correct, and it was a 6800 Vanilla, but in the end almost the same...